Re: V6.5.0.1-HP560-B19720.cim.STARTUP on msm4xx
Hello, Please try again to put the AP in boot mode: Use a paper clip or other tool to hold in the reset button for prolonged time (one will notice a slow flashing followed by a fast flashing). When...
View ArticleMSM310 (J9379A) IP Helper or DHCP Relay configuration
Hello,I recently move my DHCP server from a Cisco 887 to our own Windows 2016 DHCP server and try to add my 2 MSM 310 to this new structure as Autonomous Access points.Previously I was able to get IP...
View ArticleRe: MSM310 (J9379A) IP Helper or DHCP Relay configuration
HelloIt is not possible to configure DHCP relay on the AP. The AP will forward the wireless traffic to a wired VLAN on the switch side. It can be either the default VLAN of the AP (if you dont speficy...
View ArticleMSM460 not have "autonomus mode"
Hi All, I bought used MSM460 AP (J9591-60001:52-A, Bootware-6.6.0.0-22530), but it doesn`t have "Autonomus mode" button on web interface, only "Provision".If I try change mode from CLI, I see next...
View ArticleRe: MSM460 not have "autonomus mode"
Hello, Most probably the previous owner of the AP has used a Unified wired WLAN controller to manage this AP. Usually all you need to do is perform a factory reset with the reset button: Press and...
View ArticleRe: MSM460 not have "autonomus mode"
Thanks,I tried cim.sturtup for MSM560, my MSM460 accepted it and fix this problem
View ArticleRe: VSC to egress Internet port VLAN
wrote:I ran into a situation yesterday where I needed to have a VSC tunnel the traffic back to the 760 controller, then egress out of the Internet port on a separate VLAN. I was looking for a...
View ArticleRe: Need the xxx.cim.startup for HP 560
Hellow, Can you help me with the startup file to restore my AP please?
View ArticleMSM410 Web UI page does not appeared via IE11
Hello!We Use MSM410 under control of MSM750.I want to replace the AP for another IP address setting.I remove it and reset the AP to factory settings, the web interface page with the default IP address...
View ArticleRe: MSM410 Web UI page does not appeared via IE11
Hello, Probably the AP is running an older firmware version that still supports SSLv3 for HTTPS access. SSLv3 is not secure and for this reason it is disabled on the most current versions of the...
View ArticleRe: MSM410 Web UI page does not appeared via IE11
Thanks, Gogushev Yes, Firmware version of MSM410 is an elder vesion. 5.7.2.0 (2013)I try to edit Registory setting below, and I can access Web UI via IE11 on Windows10, Thank you!How to restrict the...
View ArticleProCurve MSM422 Access Point
HelloI have two dead access points that work as poe. Is there any chance of getting an electrical scheme of the device?
View ArticleRe: MSM710
Hello Please check below link for firmware downloadhttps://h10145.www1.hpe.com/downloads/SoftwareReleases.aspx?ProductNumber=J9325A
View Articlemsm760 msm430 waiting for acceptance
Hello, we have a msm 760 controler and msm 430 APs. Some of the APs wont't connect to the controler anymore. I already did a factory Reset on the APs and connected them directly to the 760 as a test....
View ArticleRe: msm760 msm430 waiting for acceptance
Hello, I would check the following: Check if the APs are getting their IPs in the same IP subnet where the controller has its IP address for AP discovery or in a different subnet. If the APs are in the...
View ArticleRe: ProCurve MSM422 Access Point
Hi,Please find below, J9406A HP 1-port Power Injector, that can be...
View ArticleMSM certificates expire 5/16/20
The MSM765 controller is reporting these certificates about to expire:Management Console Dummy Authority HP Management console 2010-05-19 2020-05-16Management Console Default client certificate...
View ArticleRe: MSM certificates expire 5/16/20
Updated info is in the post below from Emil_Gogushev
View ArticleRe: MSM certificates expire 5/16/20
Hello,At the moment there is no firmware version which renews this certificates and no new certificates are available for download. The question was brought to the attention of the lab and the support...
View Article