Re: Configuration of hp msm775 zl premium controller module
thank you for quick response. here is the real challenge i'm facing, im unable to make team 2 controller. i have spend 4 days doing so in the end no luck. i have follow all the user manual still no...
View Articleunable to do controller Teaming
hi everyone here is the real challenge i'm facing, im unable to make team 2 controller. i have spend 4 days doing so in the end no luck. i have follow all the user manual still no luck. can you please...
View Articlehow to change SSID password on MSM775 controller
hi everyone, i have a HP MSM775 Controller, and 3 SSID i wanted to change Wifi access Password, i have look around on Web gui but no luck, i could not found that changing WPA2 Password could you please...
View ArticleRe: unable to do controller Teaming
Controllers LAN ports are in the same subnet? No routing/firewalling between devices?Master - 192.168.0.1 , Slave 192.168.0.2Slave: Management/Teaming: enable "Controller Teaming", choose LAN-Port in...
View ArticleRe: how to change SSID password on MSM775 controller
WPA2-passwords are configured under VSC profile. Choose the VSC on left on webinface-menutree. On the right side "Wireless protection", Key source "preshared key", Key: HereIsThePassword. That's it!
View ArticleRe: Monitor MSM 760 from OpsView
I don't know OpsView. I'm using nagios/icinga and wrote a script. Script using snmp. Under "1.3.6.1.4.1.8744.5.23.1.2.1.1" there are statusinformations. Perhaps it helps?
View ArticleRe: Monitor MSM 760 from OpsView
yes - thats good - opsview is nagios with different gui. let me know if you can share this.I know nothing of monitoring and your help much appreciated.regards, michael
View ArticleRe: Single radio VSCs
On VSC-binding you are able to choose the radio, that is used to (both is default). On radio1 or radio2 you can assign 2.4 or 5GHz per accesspoint-type (f.i. MSM430)
View ArticleRe: Monitor MSM 760 from OpsView
only bash-script, hope it helps#! /bin/bashOID="1.3.6.1.4.1.8744.5.23.1.2.1.1"HOST="192.168.0.1"EXITOK=0ECHOOK=""j=0STATUS[1]="disconnected (1)"STATUS[2]="authorized (2)"STATUS[3]="join...
View ArticleRe: Teaming 2 MSM 760 Controllers - Physical Connections
i'm curious how to make it, i have the same issue here, i configure one as team manager ans require parameter including virtual ip address hhowever no luck yet i have gone through all user manual...
View ArticleRe: Teaming 2 MSM 760 Controllers - Physical Connections
Controllers LAN ports are in the same subnet? No routing/firewalling between devices? LAN-port of master connected to L2-switch; LAN-port of slave connected to same L2-switch; no vlansMaster - LAN-port...
View ArticleRe: Licencing on HP MSM controller
It's purely matter of taste. You want to build a controllerteam? Licenses where moved to other team-member if one controller is offline. You should 40x2 install to your master and the 40x1 to your...
View ArticleRe: Licencing on HP MSM controller
thanks for quick response however i'm facing trouble on teaming 2 controller here what i have doneboth controller has same clock time, timezone etci install additional licence on one controller that i...
View ArticleRe: Configuration of hp msm775 zl premium controller module
HelloI can not help you with Teaming because I have not done this. I've notice you have followup other thread. There is lots of articles on this forum about this.If you need anyother help let me know....
View Articleconnecting 2x MSM310 via lan cable
Hello everybody,I hope you can help me out with this problem. I just can't figure it out.my lan setup looks like this:one lan (192.168.1.x) with no dhcpinside this lan (192.168.1.x) I have 2 vlans...
View ArticleRe: connecting 2x MSM310 via lan cable
That's confusing me. AP1 has an default-VLAN IP 192.168.1.x on Port1. OK!WLAN-traffic (VLAN-2, VLAN3) goes tagged over Port1. OK!Switch-port should be untagged in default-VLAN, tagged in VLAN2 and...
View ArticleRe: connecting 2x MSM310 via lan cable
Hello Walter001 and thank you for your reply.the reason why I want to connect AP1 Port 2 to AP2 Port 1 is because I dont have an option to put a switch or something else in between.I will try to give...
View ArticleRe: connecting 2x MSM310 via lan cable
No way. LAN-Port is access port not trunk port. You can assign management-IP on physical-port not on VLAN-interface.If distance between APs is not so far maybe local meshing helps?
View ArticleRe: connecting 2x MSM310 via lan cable
Thank you Walter001So my idea is bulls*it =)Can you help me understand what the second port is for on the MSM310. Is it only a management port? Or can I get somehow my internet connection thru it?
View ArticleRe: connecting 2x MSM310 via lan cable
No bulls*it, but not so simple.You have to define the correct way for data-packets:AP1-port1: LAN1-IP (f.i. 192.168.0.1/255.255.255.0) + VLAN2 + VLAN3AP1-port2: LAN2-IP (f.i. 192.168.1.1/255.255.255.0)...
View Article