Re: Wifi solution fo guest users
Its listed with the MSM controller software, scroll down to other - it's the guest management...
View ArticleUpdate from 5.7.3
I have a Team environment with 2 MSM760 (5.7.3) controllers and 80 430/466 AP's.Not sure if this is possible, have not found any documentation to support it. But maybe someone has experience with...
View ArticleRe: Update from 5.7.3
Hi JRC,Please see my post reply: https://community.hpe.com/t5/M-and-MSM-Series/3-MSM-760-controllers-teaming-Software-upgrade/m-p/6915788#M5004From V6.6.2.0 release notes:IMPORTANT: If your controller...
View ArticleMSM765 started loosing the ap'S FROM THE NETWORK
Hi,I have all of sudden started loosing AP;s MSM410 & MSM 460 form controllers MSM765zl. Can any one suggest why it might be happenenig
View Articlecan you help me on msm760
good dayi have msm760, and i want to block some website at office hours, can you teach me how to setup my msm760thnx for the helping me best regardstevanus lillo
View ArticleGuest WiFi not getting an IP address only 169 Address (MSM 760)
Good Morning,I am hoping you can point me in the right direction.I have a MSM 760 controller which currently has 2 SSIDs with just WPA2 on a untagged VLAN which is working fine and gets a 10.10...
View ArticleMSM vulnerable to KRACK attacks?
Hi,a severe WiFi attack vector has been released shortly: https://www.krackattacks.com/Questions:Is MSM vulnerable to this?When will security updates be released?What measure are advisable? (E.g....
View ArticleRe: MSM vulnerable to KRACK attacks?
Aruba has reached out to the teams responsible for the HP MSM series of controllers and the HPE 8xx Unified WLAN Appliance series to obtain status. A separate security advisory will be issued...
View ArticleRe: Guest WiFi not getting an IP address only 169 Address (MSM 760)
To use HTML authentication you are forced to enable access control as well. This brings all traffic back to the controller before sending it out the VLANS set in VSC egress mapping, so these need to...
View ArticleM330
Is there any hope that these access points will get firmware that don't hang regularly?Would also be nice to know if HP is going to give a statement on if these are affected by KRACK and if they're...
View ArticleRe: MSM vulnerable to KRACK attacks?
Thank you ! Though, I'm not convinced by their statement. Opportunistic Key Caching (OKC) which is supported by HP MSM is very similar to 802.11r. I hope they'll check thoroughly. Additionally, I tried...
View ArticleRe: MSM vulnerable to KRACK attacks?
The FAQ has been updated to V1.1. Among others, there's the following new paragraph:Does the 802.11r FT handshake vulnerability also apply to OKC?A: Opportunistic key caching (OKC) is a non-standard...
View ArticleRe: MSM vulnerable to KRACK attacks?
Still not convinced. Even if we assume the fast-roaming part is uneffected, what about the mesh network feature? Using this, the access points get into the role of clients as well. That means they are...
View ArticleRe: MSM vulnerable to KRACK attacks?
Not even a whisper so far from HPE...This kind of (no)response has consequences.
View ArticleRe: M330
I, too, would like to know if these APs are vulnerable to KRACK, and if so, when the firmware will be available to fix it.
View ArticleRe: MSM vulnerable to KRACK attacks?
HPE has released a statement. Both the MSM and Unified WLAN products are not vulnerable to these attacks, including when used in mesh...
View ArticleRe: MSM vulnerable to KRACK attacks?
Thanks for sharing !Where did you get the information about mesh mode? I can't find it in the linked document.
View ArticleRe: MSM vulnerable to KRACK attacks?
Overview on more HPE products: http://h22208.www2.hpe.com/eginfolib/securityalerts/Krack%20Attack/WPA2-KrackAttack.html
View ArticleRe: MSM460 Clients getting wrong IP
I seem to be having a similar problem - just with a much later firmware version (6.6.8.0)Our clients _occasionally_ get IP addresses from the management LAN, not from the assigned VLAN. We inspected...
View ArticleFirewall see Controller IP instead of client
My MSM760 is setup as a DHCP server for a specific SSDI/VLAN. My firewall list the IP of the controller instead of the client.Can I change that so the firewall see the client IP so I can apply rules ?
View Article